# UART Source: [https://docs.qualcomm.com/doc/80-70030-8/topic/uart.html](https://docs.qualcomm.com/doc/80-70030-8/topic/uart.html) UART devices transmit data asynchronously. Hence, a clock signal doesn't synchronize the output of bits from the transmitting UART to the sampling of bits by the receiving UART. Instead of a clock signal, the transmitting UART adds start and stop bits to the data packet being transferred. These bits define the beginning and end of the data packet. This way, the receiving UART is aware of when to start reading the bits. When the receiving UART detects a start bit, it starts to read the incoming bits at a specific frequency known as the baud rate. Figure : Data transfer between two UART devices VBackground-1 Solid Page-1 Rectangle Rectangle.3 Sheet.6 Device A Device A Sheet.7 Device B Device B Square Square.9 Square.10 Square.11 Square.12 Square.13 Square.14 Square.15 Square.16 Square.17 Sheet.18 Tx Tx Sheet.19 Rx Rx Sheet.20 CTS CTS Sheet.21 RTS RTS Sheet.22 GND GND Sheet.23 GND GND Sheet.24 RTS RTS Sheet.25 Rx Rx Sheet.26 CTS CTS Sheet.27 Tx Tx Ground Sheet.29 Sheet.30 Ground.31 Sheet.32 Sheet.33 Dynamic connector.35 Dynamic connector Sheet.39 Sheet.40 Sheet.41 Sheet.42 The parameters that determine successful transmission are as follows: - Baud rate - Start bit - Stop bit - Parity bit - Data bits - Flow control The following figure shows a sample UART data packet. Figure : UART data packet VBackground-1 Solid Page-1 Rectangle 1 start bit 1 start bit Rectangle.2 5 to 9 data bits 5 to 9 data bits Rectangle.3 0 to 1 parity bits 0 to 1 parity bits Rectangle.4 1 to 2 stop bits 1 to 2 stop bits Left Brace Left Brace.9 Sheet.11 Packet Packet Sheet.17 Data frame Data frame ## UART features Source: [https://docs.qualcomm.com/doc/80-70030-8/topic/uart.html](https://docs.qualcomm.com/doc/80-70030-8/topic/uart.html) The following table describes the UART transfer modes for applications. Table : UART transfer modes | Subsystem | Transfer mode | Description | | --- | --- | --- | | Linux | | | | Boot | FIFO | | | aDSP | FIFO | | ## UART interface components Source: [https://docs.qualcomm.com/doc/80-70030-8/topic/uart.html](https://docs.qualcomm.com/doc/80-70030-8/topic/uart.html) The following table provides the paths of UART driver configurations for the different subsystems. Table : UART interface: Linux | File type | Description | | --- | --- | | Device tree source | | | `Pinctrl` settings | | | Qualcomm TEE settings |
. | Table : UART interface: Boot (UEFI-only) | File type | Description | | --- | --- | | QUP v3 serial engine configuration | | | Qualcomm TEE settings | | Table : UART interface: aDSP/SLPI | File type | Description | | --- | --- | | QUP v3 serial engine configuration | | | Firmware configuration settings | | ### UART APIs Source: [https://docs.qualcomm.com/doc/80-70030-8/topic/uart.html](https://docs.qualcomm.com/doc/80-70030-8/topic/uart.html) UART APIs for the following subsystems are listed in this section. - Linux: [https://github.com/torvalds/linux/blob/master/include/linux/tty.h](https://github.com/torvalds/linux/blob/master/include/linux/tty.h) - Boot: QcomPkg/Include/HSUart.h - aDSP: adsp\_proc/core/api/buses/uart.h ## UART software device tree configuration Source: [https://docs.qualcomm.com/doc/80-70030-8/topic/uart.html](https://docs.qualcomm.com/doc/80-70030-8/topic/uart.html) This section provides information on the UART device tree configuration, and documentation for the device nodes. ### Linux For information about Kernel device instances, see [https://github.com/torvalds/linux/blob/master/Documentation/devicetree/bindings/serial/qcom%2Cserial-geni-qcom.yaml](https://github.com/torvalds/linux/blob/master/Documentation/devicetree/bindings/serial/qcom%2Cserial-geni-qcom.yaml). For information about the UART driver files, see [https://github.com/torvalds/linux/blob/master/drivers/tty/serial/qcom_geni_serial.c](https://github.com/torvalds/linux/blob/master/drivers/tty/serial/qcom_geni_serial.c) uart7: serial@99c000 { /* Manufacturer model of serial driver */ compatible = "qcom,geni-uart"; /* SE address and size */ reg = <0 0x0099c000 0 0x4000>; /*Clocks for SE */ clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>; clock-names = "se"; /* pinctrl setting */ pinctrl-names = "default"; pinctrl-0 = <&qup_uart7_cts>, <&qup_uart7_rts>, <&qup_uart7_tx>, <&qup_uart7_rx>; interrupts = ; power-domains = <&rpmhpd SC7280_CX>; operating-points-v2 = <&qup_opp_table>; interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>, <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>; interconnect-names = "qup-core", "qup-config"; /* To enable QUPV3 serial engine instance for UART protocol, change Status to OK */ status = "disabled"; }; }Copy to clipboard For configuration settings of the serial engine GPIOs, see the following DTSI files. - QCS6490 and QCS5430: [https://github.com/torvalds/linux/blob/master/arch/arm64/boot/dts/qcom/kodiak.dtsi](https://github.com/torvalds/linux/blob/master/arch/arm64/boot/dts/qcom/kodiak.dtsi) - Dragonwing IQ-9075: [https://github.com/torvalds/linux/blob/master/arch/arm64/boot/dts/qcom/lemans.dtsi](https://github.com/torvalds/linux/blob/master/arch/arm64/boot/dts/qcom/lemans.dtsi) - Dragonwing IQ-615: [https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux.git/tree/arch/arm64/boot/dts/qcom/qcs615.dtsi?h=arm64-for-6.16](https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux.git/tree/arch/arm64/boot/dts/qcom/qcs615.dtsi?h=arm64-for-6.16) qup_uart7_cts: qup-uart7-cts-state { pins = "gpio28"; function = "qup07"; }; qup_uart7_rts: qup-uart7-rts-state { pins = "gpio29"; function = "qup07"; }; qup_uart7_tx: qup-uart7-tx-state { pins = "gpio30"; function = "qup07"; }; qup_uart7_rx: qup-uart7-rx-state { pins = "gpio31"; function = "qup07"; }; Copy to clipboard Note: The Qualcomm TEE configurations must be aligned in the QUPAC\_Access.c file to ensure that the GPIO/QUP v3 can be used. You can access the Qualcomm TEE images at /firmware/qualcomm-linux-spf-1-0\_ap\_standard\_oem\_nomodem/TZ.XF.5.0/trustzone\_images/core/settings/buses/qup\_accesscontrol/qupv3/config/<chipset>/QUPAC\_Access.c. Modify the required settings or see the default settings assigned for particular instances of the QUP v3 serial engine. QUP v3 supports both 4-wire UART with flow-control enabled, and 2-wire UART without flow control enabled. The following example for Qualcomm TEE access, controls entry for both. The QUP v3 serial engine configurations to enable the UART protocol are as follows: - Default configuration enabled for SE7 as HS UART { QUPV3_0_SE7, QUPV3_PROTOCOL_UART_4W, QUPV3_MODE_FIFO, AC_HLOS, TRUE, TRUE, FALSE }, Copy to clipboard - 2-wire UART configuration for SE5 uart5: serial@994000 { compatible = "qcom,geni-uart"; reg = <0 0x00994000 0 0x4000>; clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>; clock-names = "se"; pinctrl-names = "default"; pinctrl-0 = <&qup_uart5_tx>, <&qup_uart5_rx>; interrupts = ; power-domains = <&rpmhpd SC7280_CX>; operating-points-v2 = <&qup_opp_table>; interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>, <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>; interconnect-names = "qup-core", "qup-config"; status = "disabled"; };Copy to clipboard { QUPV3_0_SE5, QUPV3_PROTOCOL_UART_2W, QUPV3_MODE_FIFO, AC_HLOS, TRUE, FALSE, FALSE },Copy to clipboard ### Boot The QUP v3 serial engine can be configured to UART in boot using the /firmware/qualcomm-linux-spf-1-0\_ap\_standard\_oem\_nomodem/BOOT.MXF.1.0.c1/boot\_images/boot/QcomPkg/SocPkg/<chipset>/Settings/UART/UartSettings.c file. UART_PROPERTIES devices = { // MAIN_PORT 0x00994000, // Serial Engine Base address 0x009C0000,// qup_common base address 0x2001c161, // GPIO TX pin Config 0x2000c171, // GPIO RX Pin Config 0, // gpio_cts_config 0, // gpio_rfr_config 0, // clock_id_index (void*)0, // bus_clock_id (void*)CLK_QUPV3_WRAP0_S5, // core_clock_id 0, // irq number not used 0, //TCSR base 0, // TCSR offset 0 // TCSR value }; Copy to clipboard **GPIO configuration** The GPIO configuration is listed in the following table. Table : UART GPIO configuration | Bits | Parameters | | :---: | --- | | [0:3] | GPIO function | | [4:13] | GPIO number | | [14] | Direction | | [15:17] | Pull type | | [18:21] | Drive strength | You must configure each GPIO based on the following bit fields. /* | RESERVED | GPIO NUM | DRIVE | FUNC | PULL | DIR | ------------------------------------------------------------------------- | 0000 | 0000 | 0001 | 1110 | 0001 | 0001 | 0010 | 0001 | ------------------------------------------------------------------------- */Copy to clipboard ### aDSP The firmware loads SSC QUP during the bootup sequence of the aDSP subsystem. Hence, the configuration file is present in the aDSP build at /firmware/qualcomm-linux-spf-1-0\_ap\_standard\_oem\_nomodem/ADSP.HT.5.5.c8/adsp\_proc/core/settings/buses/qup\_fw/config/<chipset>/fw\_devcfg.c. The following configuration is a sample of SSC QUP SE5/6 loaded with the UART firmware in the FIFO mode. offset, protocol, mode, load_fw, dfs_mode se_cfg se0_cfg = { 0x80000, SE_PROTOCOL_I3C, GSI, TRUE, TRUE }; se_cfg se1_cfg = { 0x84000, SE_PROTOCOL_I2C, GSI, TRUE, TRUE }; se_cfg se2_cfg = { 0x88000, SE_PROTOCOL_I2C, GSI, TRUE, TRUE }; se_cfg se3_cfg = { 0x8C000, SE_PROTOCOL_I2C, GSI, FALSE, TRUE }; se_cfg se4_cfg = { 0x90000, SE_PROTOCOL_SPI, GSI, TRUE, TRUE }; se_cfg se5_cfg = { 0x94000, SE_PROTOCOL_UART, FIFO, TRUE,FALSE }; se_cfg se6_cfg = { 0x98000, SE_PROTOCOL_UART, FIFO, TRUE,FALSE }; Copy to clipboard GPIO configuration: Each serial engine in the QUP common driver is configured with the default GPIO configuration per protocol. The QUP v3 common driver picks the GPIO configuration according to the protocol loaded in the serial engine from /firmware/qualcomm-linux-spf-1-0\_ap\_standard\_oem\_nomodem/ADSP.HT.5.5.c8/adsp\_proc/core/settings/buses/qup\_common/config/<chipset>/adsp/ssc/qup\_instance\_mapping.c. The default GPIO configuration can be overwritten as follows. { .instance_id = 6 , //Instance ID .qup = QUP_SSC, //QUP Type .se_index = 5, //SE ID .se_data = NULL, //devcfg_map .protocol_io_cfg = { TLMM_MAP(TLMM_GPIO_KEEPER ,TLMM_GPIO_2MA,TLMM_GPIO_KEEPER ), //SLEEP CFG TLMM_MAP(TLMM_GPIO_NO_PULL,TLMM_GPIO_6MA,TLMM_GPIO_KEEPER ), //SPI CFG TLMM_MAP(TLMM_GPIO_NO_PULL,TLMM_GPIO_2MA,TLMM_GPIO_NO_PULL), //UART CFG TLMM_MAP(TLMM_GPIO_PULL_UP,TLMM_GPIO_2MA,TLMM_GPIO_NO_PULL), //I2C CFG TLMM_MAP(TLMM_GPIO_PULL_UP,TLMM_GPIO_2MA,TLMM_GPIO_KEEPER ) //I3C CFG }, .se_exclusive = TRUE, } Copy to clipboard TLMM\_MAP is a macro to initialize the active and sleep state GPIO configurations. For example, sample usage of the TLMM\_MAP macro. TLMM_MAP (active state pull type, drive strength, sleep state pull type)Copy to clipboard ## Enable virtualization in UART Source: [https://docs.qualcomm.com/doc/80-70030-8/topic/uart.html](https://docs.qualcomm.com/doc/80-70030-8/topic/uart.html) This section covers the high-level flow from a guest virtual machine client to the hardware port of the host machine, considering Kernel-based virtual machine (KVM) as the virtual machine. A foundational understanding of virtualization, hypervisor, and virtual machine technology is beneficial. Table : Virtualization features | Virtualization components | Feature description | | --- | --- | | VirtIO | | | Hypervisor | | ### ZigBee use case over UART in guest virtual machine To identify the device character name, enumerate the ZigBee interface in Linux as a serial interface. For example, if ZigBee is connected over UART, it's enumerated as /dev/MSMx. Note: This section uses /dev/MSM0 as an example. Replace it with the actual character device ID. 1. Disable SELinux by running the following command. setenforce 0Copy to clipboard 2. To enable KVM, do the following: 1. Boot the device to UEFI. 2. Select option 17 in the BDS menu to enter UEFI menu. 3. Select option 25 to enter OS configuration selection menu. 4. Increment the OS type to 2 (Linux with KVM) with up arrow. 5. Select Enter Power Cycle device. Wait for the device to be online. 6. Verify the device node. ls /dev/kvmCopy to clipboard 3. Push the KVM image from workspace>\builds\kvm\gunyah\_k2l\svm\lemans\_svm\svm\Image.gz. adb push Image /mnt/overlay/Copy to clipboard 4. Push the `initrd` boot image from workspace>pkondeti\builds\kvm\gunyah\_k2l\svm\lemans\_svm\svm\yocto.cpio.gz. adb push yocto.cpio /mnt/overlay/Copy to clipboard 5. To connect the device to the guest virtual machine, you can use either of the following two options. - Option **A**: For quick emulator (QEMU) virtualizer, connect the /dev/ttyMSM0 character device to the guest virtual machine using the following command. qemu-system-aarch64 \ -M virt -m 2G \ -initrd \ -kernel \ -device virtio-serial-pci \ -chardev tty,path=/dev/ttyMSM0,id=char0 \ -device virtserialport,chardev=char0,name=zigbee \ -cpu host --enable-kvm -smp 4 -nographicCopy to clipboard - Option **B**: For `libvirt` virtualizer, copy the following values into the file at [https://github.qualcomm.com/pkondeti/qli_virt_recipes/blob/main/example/hk-vm.xml](https://github.qualcomm.com/pkondeti/qli_virt_recipes/blob/main/example/hk-vm.xml).
Copy to clipboard 6. To locate and verify the `virtio-serial` virtual serial port, run the following command to list all ports. ls /dev/virtio-ports/zigbeeCopy to clipboard 7. Verify the virtual port connection. echo "hello from guest" >> /dev/virtio-ports/zigbeeCopy to clipboard Output: Hello from guestCopy to clipboard ## UART tools Source: [https://docs.qualcomm.com/doc/80-70030-8/topic/uart.html](https://docs.qualcomm.com/doc/80-70030-8/topic/uart.html) This section provides information on various test tools and methods for the UART serial interface driver to confirm the UART data transfers. ### Linux For more details, see [https://docs.kernel.org/admin-guide/serial-console.html](https://docs.kernel.org/admin-guide/serial-console.html). ## Enable UART in kernel Source: [https://docs.qualcomm.com/doc/80-70030-8/topic/uart.html](https://docs.qualcomm.com/doc/80-70030-8/topic/uart.html) This section provides information on how to enable UART in the kernel. ### Linux The following driver kernel configurations are required to support the UART interface. - UART driver: [https://github.com/torvalds/linux/blob/master/drivers/tty/serial/qcom_geni_serial.c](https://github.com/torvalds/linux/blob/master/drivers/tty/serial/qcom_geni_serial.c) - Kernel `defconfig` file path: <workspace\_path\_of\_LINUX\_kernel\_image>/sources/kernel /kernel\_platform/kernel/arch/arm64/configs/qcom\_defconfig Enable the following kernel configurations. - `CONFIG_QCOM_GENI_SE=y` - `CONFIG_SERIAL_QCOM_GENI=y` To enable a serial node for the loopback validation, apply the following patch in the /arch/arm64/boot/dts/qcom/<chipset>.dtsi file. --- a/arch/arm64/boot/dts/qcom/.dtsi +++ b/arch/arm64/boot/dts/qcom/.dtsi @@ -70,6 +70,7 @@ spi13 = &spi13; spi14 = &spi14; spi15 = &spi15; + serial1 = &uart7; }; + +&uart7 { + status = "ok"; +}; Copy to clipboard Note: You should compile the kernel configuration and device tree changes. After compilation, you can load the images to the device to verify the interface. For information about interface verification, see the [Verify UART interface](https://docs.qualcomm.com/doc/80-70030-8/topic/uart.html#uart_verification) section. ### Boot/aDSP For customizations, see the [UART software device tree configuration](https://docs.qualcomm.com/doc/80-70030-8/topic/uart.html#uart_software) section. ## UART customization Source: [https://docs.qualcomm.com/doc/80-70030-8/topic/uart.html](https://docs.qualcomm.com/doc/80-70030-8/topic/uart.html) For information about customizing UART software, see [QUP v3 access control customization](https://docs.qualcomm.com/doc/80-70030-8/topic/references.html#customize-access-control-of-qup). ## Verify UART interface Source: [https://docs.qualcomm.com/doc/80-70030-8/topic/uart.html](https://docs.qualcomm.com/doc/80-70030-8/topic/uart.html) This section describes the validation procedure for the UART drivers, and the test results for the Qualcomm drivers. ### Linux To enable the UART nodes, do the following and compile the kernel configuration. 1. To change the UART status to OKand aliases to the specific UART node, edit the following DTSI files. - QCS6490 and QCS5430: [https://github.com/torvalds/linux/blob/master/arch/arm64/boot/dts/qcom/kodiak.dtsi](https://github.com/torvalds/linux/blob/master/arch/arm64/boot/dts/qcom/kodiak.dtsi) - Dragonwing IQ-9075: [https://github.com/torvalds/linux/blob/master/arch/arm64/boot/dts/qcom/lemans.dtsi](https://github.com/torvalds/linux/blob/master/arch/arm64/boot/dts/qcom/lemans.dtsi) - Dragonwing IQ-615: [https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux.git/tree/arch/arm64/boot/dts/qcom/qcs615.dtsi?h=arm64-for-6.16](https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux.git/tree/arch/arm64/boot/dts/qcom/qcs615.dtsi?h=arm64-for-6.16) Note: Enable the SSH shell or use the ADB shell to run the commands and display the output in the SSH shell (console) window. For more information about how to run SSH, see the [Use SSH](https://docs.qualcomm.com/bundle/publicresource/topics/80-70030-254/how_to.html) section. aliases { i2c0 = &i2c0; spi15 = &spi15; ++serial1 = &uart7; }; uart7: serial@99c000 { compatible = "qcom,geni-uart"; reg = <0 0x0099c000 0 0x4000>; clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>; clock-names = "se"; pinctrl-names = "default"; pinctrl-0 = <&qup_uart7_cts>, <&qup_uart7_rts>, <&qup_uart7_tx>, <&qup_uart7_rx>; interrupts = ; power-domains = <&rpmhpd SC7280_CX>; operating-points-v2 = <&qup_opp_table>; interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>, <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>; interconnect-names = "qup-core", "qup-config"; ++status = "ok"; };Copy to clipboard 2. Disable the `if` condition in the qcom\_geni\_serial.c at [https://github.com/torvalds/linux/blob/master/drivers/tty/serial/qcom_geni_serial.c](https://github.com/torvalds/linux/blob/master/drivers/tty/serial/qcom_geni_serial.c) file for the loopback test. //if (mctrl & TIOCM_LOOP) // Disabling the if condition for loopback test port->loopback = RX_TX_CTS_RTS_SORTED;Copy to clipboard To validate the QUP v3 UART registration functionality in the Linux kernel, ensure that the UART is correctly registered with the TTY stack. 1. Disable the UART default use case in the following DTSI files. - QCS6490 and QCS5430: [https://github.com/torvalds/linux/blob/master/arch/arm64/boot/dts/qcom/kodiak.dtsi](https://github.com/torvalds/linux/blob/master/arch/arm64/boot/dts/qcom/kodiak.dtsi) - Dragonwing IQ-9075: [https://github.com/torvalds/linux/blob/master/arch/arm64/boot/dts/qcom/lemans.dtsi](https://github.com/torvalds/linux/blob/master/arch/arm64/boot/dts/qcom/lemans.dtsi) - Dragonwing IQ-615: [https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux.git/tree/arch/arm64/boot/dts/qcom/qcs615.dtsi?h=arm64-for-6.16](https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux.git/tree/arch/arm64/boot/dts/qcom/qcs615.dtsi?h=arm64-for-6.16) bluetooth: bluetooth { ++ status = "disabled"; Copy to clipboard The following output is displayed. ls /dev/ttyHS1 /dev/ttyHS1 dmesg | grep ttyH [ 3.355487] 99c000.serial: ttyHS1 at MMIO 0x99c000 (irq = 137, base_baud = 0) is a MSMCopy to clipboard 2. To verify the UART driver, do the following: 1. Open the SSH shell in permissive mode or use the ADB shell. 2. Register the UART. ls /dev/ttyHS*Copy to clipboard The following is a sample output. ls /dev/ttyHS* /dev/ttyHS1 Copy to clipboard Map the `ttyHS1` port according to the aliases added for the `serial1 = &uart7` and enable the serial engine. The UART devices registered in the kernel are listed. The UART driver follows the test sequence to enable loopback. After enabling the UART node in the DUT, run the following commands to verify that the UART instance is enabled in the DTSI file. Note: Open two SSH shells or use the ADB shell to write and read the data for the UART loopback. For more information about how to run SSH, see the [Use SSH](https://docs.qualcomm.com/bundle/publicresource/topics/80-70030-254/how_to.html) section. 1. Open the SSH shell in permissive mode or use the ADB shell. 2. Transfer data with the `echo` command. echo "This Document Is Very Much Helpful" > /dev/ttyHS1Copy to clipboard 3. Read data in the UART device node. cat /dev/ttyHS1Copy to clipboard ## Debug UART issues Source: [https://docs.qualcomm.com/doc/80-70030-8/topic/uart.html](https://docs.qualcomm.com/doc/80-70030-8/topic/uart.html) This section provides information about enabling the debug logs in the UART software driver. ### Linux UART driver logging is enabled through the dynamic debugging method. Enable `CONFIG_DYNAMIC_DEBUG` in <workspace\_path\_of\_LINUX\_kernel\_image>/sources/kernel/kernel\_platform/kernel/arch/arm64/configs/qcom\_defconfig to support the dynamic debugging for kernel drivers. To enable and view the UART driver logs in the kernel logs (`dmesg`), run the following command. mount -t debugfs none /sys/kernel/debug echo -n "file qcom_geni_serial.c +p" > /sys/kernel/debug/dynamic_debug/control echo -n "file qcom-geni-se.c +p" > /sys/kernel/debug/dynamic_debug/control echo -n "file serial_core.c +p" > /sys/kernel/debug/dynamic_debug/control echo -n "file gpi.c +p" > /sys/kernel/debug/dynamic_debug/control Copy to clipboard ## UART examples Source: [https://docs.qualcomm.com/doc/80-70030-8/topic/uart.html](https://docs.qualcomm.com/doc/80-70030-8/topic/uart.html) For information about the upstream device tree reference, see the following DTSI files. - QCS6490 and QCS5430: [https://github.com/torvalds/linux/blob/master/arch/arm64/boot/dts/qcom/kodiak.dtsi](https://github.com/torvalds/linux/blob/master/arch/arm64/boot/dts/qcom/kodiak.dtsi) - Dragonwing IQ-9075: [https://github.com/torvalds/linux/blob/master/arch/arm64/boot/dts/qcom/lemans.dtsi](https://github.com/torvalds/linux/blob/master/arch/arm64/boot/dts/qcom/lemans.dtsi) - Dragonwing IQ-615: [https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux.git/tree/arch/arm64/boot/dts/qcom/qcs615.dtsi?h=arm64-for-6.16](https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux.git/tree/arch/arm64/boot/dts/qcom/qcs615.dtsi?h=arm64-for-6.16) For information about device-tree node for the Qualcomm Linux hardware SoCs, see the following DTSI files. - QCS6490 and QCS5430: [https://github.com/torvalds/linux/blob/master/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts](https://github.com/torvalds/linux/blob/master/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts) - Dragonwing IQ-9075: [https://github.com/torvalds/linux/blob/master/arch/arm64/boot/dts/qcom/lemans.dtsi](https://github.com/torvalds/linux/blob/master/arch/arm64/boot/dts/qcom/lemans.dtsi) - Dragonwing IQ-615: [https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux.git/tree/arch/arm64/boot/dts/qcom/qcs615.dtsi?h=arm64-for-6.16](https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux.git/tree/arch/arm64/boot/dts/qcom/qcs615.dtsi?h=arm64-for-6.16) Last Published: Jul 03, 2026 [Previous Topic Getting started: Set up the device interface](https://docs.qualcomm.com/bundle/publicresource/80-70030-8/topics/get-started.md) [Next Topic SPI](https://docs.qualcomm.com/bundle/publicresource/80-70030-8/topics/spi.md)