# Hardware overview
The Qualcomm RB3 Gen 2 Development Kit is available as a Core Kit and a Vision Kit. Both kits feature a system-on-module (SoM) that integrates a Qualcomm system-on-chip (SoC).
The SoM is mounted to an interposer that’s connected to the mainboard using a 500-pin connector.
The mainboard includes many connectors to support a variety of different peripheral interfaces and stackable mezzanine cards.
The Vision Kit includes everything in the Core Kit plus the Qualcomm Vision mezzanine board, a high-resolution main camera, and a low-resolution tracking camera.
>
>
> 
The following video shows the architecture of the RB3 Gen 2 Development Kit hardware and the location of the interfaces, buttons, LEDs, DIP switches, and connectors.
>
>
>
>
>
> **RB3 Gen 2 Development Kit — 360° walkthrough**
The following video shows the unboxing and setup of the RB3 Gen 2 Development Kit. It also shows running a sample app on the kit.
>
>
>
>
>
> **RB3 Gen 2 Development Kit unboxing and setup**
Note
The RB3 Gen 2 Vision Kit includes cameras with protective lens covers. Remove these covers before using the kit.
Kit components
| Core Kit | Vision Kit |
| --- | --- |
|
Qualcomm RB3 Gen 2 mainboard
Interposer with SoM
Power supply (12 V)
USB-A to USB-C cable
Two speakers
Pick tool to help access DIP switches
|
Qualcomm RB3 Gen 2 Core Kit
Qualcomm Vision mezzanine board
IMX577 camera
OV9282 tracking camera
|
**Mainboard and interposer block diagram**
The following block diagram shows the RB3 Gen 2 mainboard and interposer. Connectors are shown in dark blue. Some connectors are on the interposer board and some on the mainboard.
Knowing the placement of these connectors is useful in configuring and debugging them easily and effectively.
>
>
> 
>
> **Mainboard and interposer block diagram**
Hardware features in RB3 Gen 2 Dev Kit
| Feature | Component name | Interface | Details |
| --- | --- | --- | --- |
| DSI to HDMI bridge | Lontium LT9611UCX | HDMI Type-A connector | 4K at 30-Hz HDMI support with I2S audio |
| USB hub | Genesys GL3590 | 2x USB Type-A connectors | USB 3.1 Gen2 10 Gb 4-port hub controller |
| USB to LAN | ASIX AX88179 | RJ45 connector | USB 3.0 Gb to 1 Gb Ethernet controller |
| Audio amplifiers (2) | Qualcomm WSA8835 | Header pins (2) on interposer | Class-D SoundWire audio amplifier |
| CAN bus controller | Microchip MCP2518FD | Pins on LS1 connector | External CAN-FD controller with SPI |
| Sensor | TDK ICM-42688-P | Sensor on mainboard | 3-axis gyroscope and 3-axis accelerometer |
| On-board digital microphone | TDK T5818 | Microphone on mainboard | PDM digital MEMS microphone |
| USB host/Device port | USB Type-C | Type C connector | USB Type-C with display port (direct connect to processor) |
| Input power | DC power input | Barrel jack connector | +12-V from wall supply |
| microSD storage | microSD card | microSD card tray | microSD card tray |
| WLAN/Bluetooth antenna | Antenna0 | Printed antenna on mainboard | 2.4 GHz/5 GHz printed antenna |
| WLAN/Bluetooth antenna | Antenna1 | Printed antenna on mainboard | 2.4 GHz/5 GHz printed antenna |
| Debug UART | FTDI UART to USB converter | microUSB connector | Connector with FTDI USB to UART converter |
| DP display | DP display output | Micro DisplayPort connector (on interposer) | Display only, not including touch or backlight control |
| GNSS | SDR735G chipset | RF connector for external antenna on interposer | GNSS/GPS support |
| USB 2.0 | USB1 port from SoC | Micro USB connector on interposer | Additional USB port for host/ device mode |
| Second Ethernet port | From QPS615 PCIe expander | IX Ethernet connector on interposer | 2.5 GbE from PCIe |
| Third Ethernet port | From QPS615 PCIe expander | IX Ethernet connector on interposer | 10 GbE from PCIe (not installed by default, special order) |
| Camera port 1 | From chipset | 30-pin flex connector | Support for C/D-PHY camera |
| Camera port 2 | From chipset | 30-pin flex connector | Support for C/D-PHY camera |
## Status LEDs and buttons
The following figure shows the LEDs and buttons on the RB3 Gen 2 mainboard.
>
>
> 
>
>
> **[L] Top view of mainboard LEDs and buttons, [R] bottom view**
The following LED colors indicate different statuses:
- Yellow LED is for Wi-Fi status.
- Blue LED is for Bluetooth status.
The F\_DL button is used for emergency boot. In addition to volume control, Vol- is also used to reset the device.
## Mainboard and interposer connectors
The following figures show the location of the different connectors on the mainboard and interposer. The image at left shows the connectors from the top view of the mainboard.
The image at right shows the connectors from the bottom view of the interposer board (outlined in yellow) attached to the mainboard. The bottom view is shown with the baseplate removed.
>
>
> 
>
> **[L] Connectors on top view of mainboard, [R] bottom view of interposer (in yellow) and mainboard**
Low-speed connectors (LS1, LS2, LS3) and high-speed connectors (HS1, HS2, HS3) provide various functionalities including UART, SPI, camera CSI, interrupt signals, DC power, and additional GPIOs.
See [low-speed and high-speed expansion connectors](https://docs.qualcomm.com/doc/80-80015-251/topic/references.html#ls-hs-connectors) for details.
## Vision mezzanine
The Vision mezzanine supports interfacing cameras to the RB3 Gen 2 platform through two, second-generation gigabit multimedia serial link (GMSL2) camera inputs and five CAM/CSI camera ports. This mezzanine also has four DMICs, an IMU, compass/magnetometer, and a pressure sensor.
>
>
> 
>
> **Vision mezzanine**
The following block diagram shows components and connectors on the mainboard and Vision mezzanine.
>
>
> 
>
> **Vision mezzanine and mainboard block diagram**
The following key components are supported on the Vision mezzanine:
**Camera**
- Two GMSL2 camera inputs (using MAX9296A), CSI4 and CSI5. Labels on board (GMSL1 and GMSL2) are connector names only. Both inputs are GMSL2 technology.
- Five CAM/CSI camera ports with identical pinouts: CSI0 splits into two cameras (CAM0A and CAM0B)
- CAM3 connector includes an option for a higher supply voltage of 5 V and accommodates the Panasonic TOF camera
- Main camera (IMX577); part number: CMK-IMX577-B-V2.0, connect to CAM3
- Tracking camera (OV9282); part number: CMK-VR-OV9282-V1.0, connect to CAM0A
**Sensors**
- DK ICM-42688-P IMU (located on the back side of the board)
- AKM compass/magnetometer AK09919
- TDK pressure sensor (ICP-10111)
**Audio**
- Four digital PDM mics that interface directly with the RB3 Gen 2 platform
- Speaker connectors on the mezzanine are inactive. They’re replaced by the speaker connectors located on the interposer. For more information, see Mainboard and interposer connectors.
## Sensors
Sensors are available on the mainboard and the vision mezzanine. Only one IMU sensor can function at a time. If both sensors are enabled, only the Vision mezzanine IMU functions. The following table lists the sensor details and identifies the appropriate DIP switch for each sensor. See [DIP switches](https://docs.qualcomm.com/doc/80-80015-251/topic/references.html#dip-switches) for DIP switch locations.
| Placement | Sensor part | Sensor type | DIP switch | Name | Details | Default |
| --- | --- | --- | --- | --- | --- | --- |
| Mainboard | ICM42688 | Inertial Measurement Unit (IMU) sensor: Accelerometer and Gyroscope | DIP\_SW\_0 (pin 5) | SENSOR\_IM U\_TOGGLE |
| ON |
| | | | | | | |
| | | | | | | |
| | | | | | | |
## Ethernet
The RB3 Gen 2 Development Kit has a gigabit Ethernet interface on the mainboard through an RJ45 connector and a 2.5GbE Ethernet interface on the interposer board through an IX connector.
An adapter cable, which isn’t part of the kit, is required to use the IX connector. An adapter cable is available as an optional accessory for additional purchase.
>
>
> 
>
> **[L] Ethernet connector on top view of mainbaord, [R] Ethernet connector on bottom view of interposer**
Hover over each step in the following snippet of the mainboard and interposer diagram to see a high-level description of the Ethernet functionality, flow, and components in the RB3 Gen 2 Development Kit.
On the interposer board, the PCIe1 2L signals are connected to the QPS615 (PCIe bridge).
SGMII signals from the QPS615 are connected to QEP8121 PHY and terminated to the IX connector supporting 2.5GbE.
Based on the DIP SW 3 (bit 2) settings, the QPS 1 lane PCIe signals are connected to either PCIe to USB (uPD720201) where it is converted to USB or routed straight to the 500-pin connector. The default switch position is to select the path via PCIe to USB (uPD720201).
The mainboard has the USB 3.1 Gen2 Hub (4) along with USB to LAN (AX88179) which is terminated to the RJ 45 connector.
## Mainboard RF antennas
The RB3 Gen 2 mainboard uses two dual-band, 2.4 GHz/5 GHz/6 GHz, WLAN/Bluetooth technology printed antennas on the mainboard. To avoid detuning the antennas, use nylon standoffs for mounting holes and check that there is no metal directly above or below
the antennas. QCS6490/QCS5430 supports 2 × 2 MIMO with 2x Wi-Fi antenna ports and 1x Bluetooth technology antenna port. The current SoM uses a shared Wi-Fi/Bluetooth technology approach on RF Chain0. The SoM has the option to route RF signals through
the board-to-board connector to the mainboard to eliminate the need for external coaxial cables (current configuration).
>
>
> 
>
> **Dual-band RF antennas on the mainboard (bottom view)**
As shown in the following image, connectors are available on the interposer to connect high-performance external antennas (optional, not included in the kit). A GNSS connector is also available. Use Ipex MHF-SW 23 series cables to connect external antennas.
>
>
> 
>
> **Dual-band RF antenna and GNSS connectors on the interposer**
## Next steps
To get started, see the [RB3 Gen 2 Quick Start Guide](https://docs.qualcomm.com/doc/80-80015-253/topic/qsg-landing-page.html).
To learn more, see [Reference designs and related documents](https://docs.qualcomm.com/doc/80-80015-251/topic/rel-docs.html#rel-docs).
Last Published: Dec 08, 2025
[Previous Topic
Introduction](https://docs.qualcomm.com/bundle/publicresource/80-80015-251/topics/introduction.md) [Next Topic
Power up and power cycle](https://docs.qualcomm.com/bundle/publicresource/80-80015-251/topics/rb3_mainboard_power.md)
Source: [https://docs.qualcomm.com/doc/80-80015-251/topic/rb3_hardware_overview.html](https://docs.qualcomm.com/doc/80-80015-251/topic/rb3_hardware_overview.html)